Waterproof rating and testing standards
Guoan Energy Technology (Dongguan) Co., Ltd. R&D Center
Protection level IP54, IP is the marking letter, the number 5 is the first marking number, and 4 is the second marking number. The first marking number indicates the level of contact protection and foreign object protection, and the second marking number indicates the level of waterproof protection;
Contact protection and foreign object protection level (first digit) Waterproof protection level (second digit)
|
First digit |
Protection content |
Second digit |
Protection range |
||
|
Name |
Description |
Name |
Description |
||
|
0 |
No protection |
- |
0 |
No protection |
- |
|
1 |
Protection against solid foreign bodies with a diameter of 50mm and larger |
Detector, sphere diameter is 50mm, should not enter completely |
1 |
Water drop protection |
Vertically falling water droplets should not cause damage |
|
2 |
Protection against solid foreign bodies with a diameter of 12.5mm and larger |
Detector, sphere diameter is 12.5mm, should not enter completely |
2 |
Cabinet tilted 15 degrees, protection Water drops |
When the cabinet is tilted 15 degrees to either side, vertically falling water droplets should not cause damage |
|
3 |
Protection against solid foreign bodies with a diameter of 2.5mm and larger |
Detector, sphere diameter is 2.5mm, should not enter completely |
3 |
Protection against splashing Water |
Water splashing from both sides of the vertical line at a 60-degree angle should not cause damage |
|
4 |
Protection against solid foreign bodies with a diameter of 1.0mm and larger |
Detector, sphere diameter is 1.0mm, should not enter completely |
4 |
Protection against spraying water |
Spraying water from each direction at the cabinet should not cause damage |
|
5 |
Dust protection |
It is impossible to completely prevent dust from entering, but the amount of dust entering will not cause damage to the equipment |
5 |
Protection against jetting water |
Jetting water from each direction at the cabinet should not cause damage |
|
6 |
Dustproof |
Dust should not enter the cabinet at a low pressure of 20 mbar |
6 |
Protection against strong jetting water |
Strong jetting water from each direction at the cabinet should not cause damage |
|
|
7 |
Protection against short-term immersion Water |
When the cabinet is briefly immersed in water under standard pressure, no amount of water that could cause damage should enter |
||
|
Note: The diameter of the detector should not pass through the holes in the cabinet |
8 |
Protection against long-term immersion Water |
Can be immersed in water under specific conditions, no water that could cause damage should enter |
||

Waterproof test
Range
Waterproof tests include the second characteristic digit from 1 to 8, i.e., the protection level code is IPX1 to IPX8.
2. Content of waterproof tests of various levels
(1) IPX1
Method name: Vertical dripping test
Test equipment: Dripping test device and its test method see 2.11
Sample placement: Place the sample in its normal working position on a rotating sample table with a rotation speed of 1 r/min. The distance from the top of the sample to the dripping point is no more than 200mm
Test conditions: Dropping amount is 1 ± 0.5 mm/min;
Test duration: 10 min;
(2) IPX2
Method name: Tilting 15° dripping test
Test equipment: Dripping test device and its test method see 2.11
Sample placement: Make one side of the sample at a 15° angle to the vertical line. The distance from the top of the sample to the dripping point is no more than 200mm. After testing one side, change to another side, for a total of four times.
Test conditions: Dropping amount is 3 ± 0.5 mm/min;
Test duration: 4 × 2.5 min (total 10 min);
(3) IPX3
Method name: Spraying test
Test method:
a. Swing pipe spraying test
Test equipment: Swing pipe spraying and splashing test device
Sample placement: Select a swing pipe with an appropriate radius, so that the height of the sample table is at the diameter position of the swing pipe, place the sample on the sample table, so that the distance from its top to the sample spray nozzle is no more than 200mm, and the sample table does not rotate.
Test conditions: The water flow rate is calculated according to the number of spray holes in the swing pipe, 0.07 L/min per hole. When spraying, the spray from the spray holes in the 60° arc segment on both sides of the midpoint of the swing pipe is directed at the sample. The sample is placed in the center of the semicircle of the swing pipe. The swing pipe swings 60° on both sides of the vertical line, for a total of 120°. Each swing (2 × 120°) takes about 4s.
Test time: Continuous spraying for 10 min.
b. Nozzle spraying test
Test equipment: Handheld spray and splash test device. The device diagram and test method can be found in Section 2.14 of this book.
Sample placement: The parallel distance between the top of the test sample and the water nozzle of the handheld spray head should be between 300mm and 500mm.
Test conditions: A baffle plate with a counterweight should be installed during the test, and the water flow rate should be 10 L/min.
Test time: Calculated according to the surface area of the sample's outer casing, 1 min per square meter (excluding the installation area), minimum 5 min.
(4) IPX4
Method name: Splash test;
Test method:
a. Swinging pipe splash test
Test equipment and sample placement: The same as item (3) IPX3 a above;
Test conditions: The same as item (3) IPX3 a above, except for the following conditions;
The spray area is the spray direction of the spray holes within 90° arc segments on both sides of the midpoint of the swing pipe towards the sample. The sample is placed in the center of the semicircle of the swing pipe. The swing pipe swings 180° on each side of the vertical, totaling approximately 360°. Each swing (2 × 360°) takes approximately 12s.
Test time: The same as item (3) IPX3 a above (i.e., 10 min).
b. Nozzle splash test
Test equipment and sample placement: The baffle plate with counterweight installed on the equipment should be removed; the rest is the same as item (3) IPX3 b above;
Test conditions: The same as item (3) IPX3 b above, except for the following conditions;
Test time: The same as item (3) IPX3 b above, i.e., calculated according to the surface area of the sample's outer casing, 1 min per square meter (excluding the installation area), minimum 5 min.
(5) IPX5
Method name: Water jet test
Test equipment: The inner diameter of the nozzle's water outlet is 6.3 mm; The device diagram and test method can be found in Section 2.14 of this book.
Test conditions: The distance between the test sample and the water outlet is 2.5-3 m, and the water flow rate is 12.5 L/min (750 L/h);
Test time: Calculated according to the surface area of the sample's outer casing, 1 min per square meter (excluding the installation area), minimum 3 min.
(6) IPX6
Method name: Strong water jet test;
Test equipment: The inner diameter of the nozzle's water outlet is 12.5 mm; The device diagram and test method can be found in Chapter 2.14 of this book;
Test conditions: The distance between the test sample and the water outlet is 2.5-3 m, and the water flow rate is 100 L/min (6000 L/h);
Test time: Calculated according to the surface area of the sample's outer casing, 1 min per square meter (excluding the installation area), minimum 3 min.
(7) IPX7
Method name: Short-term immersion test;
Test equipment and test conditions: Immersion tank. Its dimensions should allow the sample to be placed in the immersion tank with a distance of at least 1 m between the bottom of the sample and the water surface. The distance between the top of the sample and the water surface should be at least 0.15 m.
Test time: 30 min.
(8) IPX8
Method name: Continuous submersion test;
Test equipment, test conditions, and test time: To be agreed upon by both the supplier and the purchaser. The severity should be higher than IPX7.
International industrial standard waterproof rating IPX grading standard
The international industrial waterproof rating standard IPX and the Japanese industrial waterproof standard JIS rating are consistent, divided into 9 levels from 0-8, recorded here.
|
Level 0 |
Level 0 No protection |
|
Level 1 |
Level 1 Can eliminate the harmful effects of vertically falling water droplets |
|
Level 2 |
Level 2 Protection against water droplets falling within 15 degrees of the vertical direction |
|
Level 3 |
Level 3 Can eliminate the harmful effects of spray-like water droplets at 60 degrees to the vertical direction |
|
Level 4 |
Level 4 Can eliminate the harmful effects of splashing water droplets from different directions |
|
Level 5 |
Level 5 Can eliminate the harmful effects of water jets sprayed from all directions |
|
Level 6 |
Level 6 Can eliminate the harmful effects of strong water jets sprayed from all directions |
|
Level 7 |
Level 7 Top 0.15-1 meter from the water surface, continuously for 30 minutes, performance unaffected, no leakage |
|
Level 8 |
Level 8 Top 1.5-30 meters from the water surface, continuously for 30 minutes, performance unaffected, no leakage |
Dustproof rating (the first X indicates)
0: No protection 0: No protection
1: Objects with a diameter of 50 mm shall not be able to fully enter the casing
2: Objects with a diameter of 12.5 mm shall not be able to fully enter the casing
3: Water dripping within 60 degrees on each vertical plane, without harmful effects
4: Objects with a diameter of 1.0mm must not enter the shell.
5: Dust ingress cannot be completely prevented, but the amount of dust entering must not affect the normal operation of the equipment or compromise safety.
6: No dust ingress.
Waterproof rating (second X indicates)
1: No harmful effects from vertically dripping water.
2: No harmful effects from vertically dripping water when the vertical surfaces of the enclosure are tilted within a 15-degree range.
3: Objects with a diameter of 2.5mm must not enter the shell.
4: No harmful effects from water splashing in any direction onto the enclosure.
5: No harmful effects from water jets in any direction onto the enclosure.
6: No harmful effects from strong water jets in any direction onto the enclosure.
7: No effect from short-term immersion in water.
8: No effect from continuous submersion in water.
Example: A waterproof box with a waterproof rating of IP65 indicates that the product can completely prevent dust from entering and can be washed with water without any
Service Hotline
Email:zhangjie@ganeny.com
Website:www.ganeny.com
Address: No. 79, Shayuan Road, Shabu, Dalang Town, Dongguan City, Guangdong Province, China
Official Public Account
Privacy Policy | SEO | Support:300.cn
